Search results

  1. G

    Walbro 255lph GSS342G3 Fuel Pump Install

    Yes. You need the sleeve to match the diameter of the original clamp. I know I order mine separate an took a look at the thickness of the sleeve. I think it was about 1/8 to 1/4" thick.
  2. G

    Walbro 255lph GSS342G3 Fuel Pump Install

    Still going strong with the same fuel pump. Amazon is decent at filtering out knock offs, but the ebay one has the sleeve that you will need. I have no idea if either is genuine, but they should be. I know I used Ebay for mine, but no idea who sellers was at this point.
  3. G

    pontiac truck

    Did you put the Whiteline bushing on the correct side? The offset should be further to the outside on both sides. I have had no issues with either a 1 degree and 1.5 degree offset control arm bushings. Did you take off the front bracket that the front lower control arms slides onto? It is...
  4. G

    Ignition Distributor Rotor

    On ebay I see some still that can be bought from U.K. I saw some fitment from a Subaru, and a Nissan, but I think these are going to dry up also. If you still have the one kit left rotor, cap, o-ring, and set screw I will buy it from you.
  5. G

    pontiac truck

    When I did the addition of rear sway bar and all new front poly with an offset bushing for control arm I was starting to think that something was screwy until I realized that I didn't fully torque down one of the strut nuts. I drove it to work and it ran alright on the way to work, but was...
  6. G

    Wrecked and Neglected Barn Find GT

    Nice job on the restore. The pedal travel on a larger Wilwood system front and back is perfect in my opinion with the stock master cylinder. Yes, you lose the hydraulic force (the same force doesn't occur). It is about 100 lbs (69 psi) of force difference if you keep the pedal pressure the...
  7. G

    GTi Pistons

    I'm not aware of any stock oversized left out there. If you do find anything let us know. I see the ITM aftermarket oversized are only available in one size now and come with a matching set of rings.
  8. G

    sprint turbo or gti?

    I'm not a fan of people grabbing engines from our platform for other cars because they tend to never make it back to our platform. The Suzuki Samurai owners are a different breed of people and they tend to destroy our 1.3 dohc engines. At least it is a Suzuki. That aside. There are a lot...
  9. G

    Updating My turbo GTi

    The 1989 to 1994 base Swifts came with filler ports and the GT(i) came with fog lights. They are not brake duct port, but just filler. They do work well for aftermarket fog lights as you can put a circle fog lamp inside the them. You could pick them up at a wrecking yard.
  10. G

    pontiac truck

    It has been about the same temperature here and I did the stereo install under the shade of a tree to make it much cooler install. Are those tires winter tires?
  11. G

    92 Black GT

    I switched over to the new stereo wiring harness today. Soldered up everything with shrink heat wrap. I realized that I have a double din already in the car. I was happy with the wiring job it looked super clean. Tomorrow, I will finish the Kenwood stereo install which really is just...
  12. G

    GTi rear brake caliper alternative.

    I had looked at making a rear caliper bracket from a 90's Honda with rear disc brakes. They use the a similar emergency brake caliper. I would have to find which particular one I was looking at again. I remember looking for something that still had aftermarket support for different pads. I...
  13. G

    1990 White GT Back-Up Car

    I have a white four door metro that I could switch everything to. There are not too many four door metros with a g13b engine in them.
  14. G

    92 Black GT

    Everything is working! She is back on the road.
  15. G

    92 Black GT

    A little less then a month later and I finally got around to installing the transmission and got her fired up last night. I need to do a test drive as I was way to tired last night.
  16. G

    pontiac truck

    White line has the wrong part listed for the end link bushings. Somewhere on my black gt post I have the numbers listed, but I just use the energy suspension poly ones.
  17. G

    1990 White GT Back-Up Car

    I clean out the glass today, and but in a window I picked up from a local forum member from Geometroforum. I tried fixing the door, but no real luck. It is hard to get to the internal part of the door. This is the same for the roof I could not get to the pinched part of the tent on the edge...
  18. G

    WTB Swift/Metro 89 to 94 White Right/Passenger Door

    My white 90 Suzuki Swift GT took a tree to the right/passenger door in the last wind storm. Looks like I can get a window and local pick in pull but I doubt I can fix the door. Needs to be 2 door hatch back door.
  19. G

    Whiteline bushings

    Superpro bushings SPF0678K front lower control front position are in stock at Suspension.com but the crush tubes that came with the Superpro sealed bags were the wrong interior size. I had to mill them out to make them work. Suspension.com had the 1" cast front control arm rear position...
  20. G

    1990 White GT Back-Up Car

    She took a hit from a good sized tree couple days ago. Passenger door is most likely not fixable on top of the window being completely busted out. I took a hard hit to the middle of the door edge and roof. I was able to pop the middle back out, but I will have to take the ceiling panel off...
Back
Top