93 Swift Chevy Turbo

She is back up an running. I'm using her for my commute. Still running relatively low boost until she is broken in. I am going to purchase a electronic boost controller and then install the manual boost controller on this car.
 
Updates:
 

Attachments

  • Block 2 w ARP head Studs.jpg
    Block 2 w ARP head Studs.jpg
    478.5 KB · Views: 8
  • Block 3.jpg
    Block 3.jpg
    490.8 KB · Views: 5
  • Block Close Up w Check Valve.jpg
    Block Close Up w Check Valve.jpg
    566.4 KB · Views: 4
  • Block w ARP studs.jpg
    Block w ARP studs.jpg
    462.8 KB · Views: 4
  • Block with Bearings 2.jpg
    Block with Bearings 2.jpg
    603.9 KB · Views: 4
  • Block with Bearings.jpg
    Block with Bearings.jpg
    642.2 KB · Views: 4
  • Bottom End Complete 2.jpg
    Bottom End Complete 2.jpg
    577 KB · Views: 4
  • Bottom w Oil Pick Up Tube.jpg
    Bottom w Oil Pick Up Tube.jpg
    610.4 KB · Views: 5
  • Bottom End Complete.jpg
    Bottom End Complete.jpg
    610.4 KB · Views: 7
More Updates:
 

Attachments

  • Clutch 1.jpg
    Clutch 1.jpg
    128.6 KB · Views: 6
  • Clutch 2.jpg
    Clutch 2.jpg
    115.8 KB · Views: 6
  • Clutch 3.jpg
    Clutch 3.jpg
    99.3 KB · Views: 5
  • Clutch 5.jpg
    Clutch 5.jpg
    114 KB · Views: 4
  • Clutch 7.jpg
    Clutch 7.jpg
    133 KB · Views: 5
  • Driverside Front View.jpg
    Driverside Front View.jpg
    209.7 KB · Views: 5
  • Crankshaft.jpg
    Crankshaft.jpg
    503.6 KB · Views: 5
  • Driverside View.jpg
    Driverside View.jpg
    309.3 KB · Views: 5
  • engine bay 1.jpg
    engine bay 1.jpg
    125 KB · Views: 6
Even more updates:
 

Attachments

  • Engine 1.jpg
    Engine 1.jpg
    219.8 KB · Views: 7
  • engine bay 1.jpg
    engine bay 1.jpg
    125 KB · Views: 5
  • Engine bay 3.jpg
    Engine bay 3.jpg
    99.5 KB · Views: 5
  • Engine bay 2.jpg
    Engine bay 2.jpg
    123.7 KB · Views: 5
  • Engine bay 6.jpg
    Engine bay 6.jpg
    123.7 KB · Views: 5
  • Engine Bay Driverside.jpg
    Engine Bay Driverside.jpg
    235.3 KB · Views: 5
  • Engine Bay Front.jpg
    Engine Bay Front.jpg
    213.9 KB · Views: 5
  • Engine Bay Passenger Side.jpg
    Engine Bay Passenger Side.jpg
    266.8 KB · Views: 5
  • Engine Installation 1.jpg
    Engine Installation 1.jpg
    115.4 KB · Views: 5
  • Engine Installation 2.jpg
    Engine Installation 2.jpg
    129 KB · Views: 8
I installed a rear sway bar with Energy Suspension poly bushings. I used a 1/2" plate aluminum on bottom and a 1/4" plate of aluminum on top on each sway bar bushing mount. I also pulled the rack and pinion and replaced inside and outside tie rods with new bellows. I cleaned up the rack, and greased.
 
I have been driving her for my daily for a bit. Steering is way better after doing new inside and outside tie rods. When I first put back on the rack I had reversed the bushing sleeve on the passenger side of the rack. I noticed right away that something wasn't right. Took it all back off and flipped it and she was good to go. I still need to replace front bushings and get a proper alignment since I got her as close as I could without the right equipment. I will also do new front suspension also before doing the alignment.
 
Back
Top